Showing posts with label MP. Show all posts
Showing posts with label MP. Show all posts

Tuesday, June 10, 2014

MICROPROCESSOR (MP) DECEMBER 2011 COMPUTER SCIENCE SEMESTER 5

MICROPROCESSOR (MP) DECEMBER 2011 COMPUTER SCIENCE SEMESTER 5

Q.1   A)Explain in brief yhe interupts in Intel 8085 up.(5)
        B)Draw the circuit diagram for generation of RESET signal and explain it's working.(5)
        C)Design an interface for 8255 with the following requirements: 1, 16-bit I/P and(5)
1, 16-bit O/P port. Starting address is 20000H.
        D)Differentiate between the Memory mapped I/O and I/O mapped I/O.(5)

Q.2   A)

Design 8086 based system with following specifications:

(10)
a) Interface 32 KB SRAM. Use IC 6264.
b) Interface 16 KB DRAM. Use 8 KB Chips.
        B)Explain the following Intel 8086 assembly language instructions giving example:(10)
a) SAL, b) TEST, c) DAA, d) JA, e) NOP.

Q.3   A)

Explain the operation of IC 8254 as a square wave generator with the control

(5)
word and timing diagram for count value of 4.
        B)IC 8255 is interfaced with Intel 8086 at an address 2006H. Write a set of(5)
statements in assmbly language to initialize it such that Port A will be in
mode 2, Port B will be in model 1 Output.
        C)Explain the operation of IC 8259 with the block diagram. Explain all the(10)
signals in detail.

Q.4   A)

Write an Assembly language program for Intel 8086 processor to perform the
(5)
division of 2 digit BCD number which is in unpacked form.
        B)Explain the fully nested mode of PIC 8259.(5)
        C)Explain the modes of operation of a DMA Controller.(10)

Q.5   A)

Explain following addressing modes of Intel 8086. Write an instruction for each

(5)
mode:
a) Direct addressing mode, b) Relative base indexed.
        B)Draw the flowchart for intilization sequence of PIC 8259.(5)
        C)What do you understand by bus arbitration? Explain the different bus arbitration(10)
techniques with diagram.

Q.6   A)

Explain the memory segmentation in Intel 8086 processor with it's advantages &

(5)
diadvantages.
        B)Explain the status signals of Intel 8086 processor. Show all the possible(5)
combination along with the processor state and 8288 command associated with each
combination.
        C)Explain the operational command words of PIC 8259.(10)

Q.7)

Explain the following in brief:-

(20)
A) RS 232C interface
B) Fixed and Variable port addressing formats
C) Address decoding techniques
D) Difference between Software and Hardware interupts.

MICROPROCESSOR (MP) MAY 2011 COMPUTER SCIENCE SEMESTER 5

MICROPROCESSOR (MP) MAY 2011 COMPUTER SCIENCE SEMESTER 5 

                                                                     (3 Hours)                                  [Total Marks: 100]

1. Design a 8086 Based system consisting of the following:- [20 Marks]
    (a) 8086 microprocessor working at 8 MHz.
    (b) EPROM of 64 KB using 32 KB  devices.
    (c) SRAM of 64 KB using 16 KB devices.
    (d) One input and one output port (both 16 bit) interrupt driven.
          Explain the design. Also show the memory and I/O map.

2. (a) Explain the Initialization Command Words (ICWs) and Operational Command Words (OCWs)
         of the 8259 PIC. [10 Marks]   
    (b) What is segmented memory? State the advantages of segmentation with reference to the
          8086 microprocessor. Also explain the default segment assignments. [10 Marks]

3. (a) Explain the programmer's model of the Inter 8085 microprocessor. [10 Marks]
    (b) Describe the various system bus arbitration schemes in loosely coupled systems. [10 Marks]

4. (a) Explain the interrupt structure of the 8086. Discuss the functions of the pre-defined /
         dedicated interrupts. [10 Marks] 
    (b) Write a detailed note on the 8289 Bus arbiter. Emphasis on its role in a multiprocessor
          system. [10 Marks] 

5. (a) Explain the operating modes of the 8255 PPI. Also explain the handshaking operation for input
         and ouput in model. [10 Marks]
    (b) Compare the 8085 and 8086 microprocessor w.r.t architecture, instruction, set, speed,
          memory, organization. [10 Marks]

6. (a) What is meant by Direct Memory Access? Show as interfacing diagram of 8086
          microprocessor with 8237 DMD controller. [10 Marks]
    (b) Write a detailed note on the branch instructions of the 8086. [10 Marks]

7. Write short notes on:- [20 Marks]
     (a) IEEE-488 GPIB standard.
     (b) Addressing modes in the 8086.
     (c) 8284 clock generator.
     (d) Modes of operation of the 8253-PIT.

Monday, June 9, 2014

MICROPROCESSOR (MP) DECEMBER 2010 COMPUTER SCIENCE SEMESTER 5

MICROPROCESSOR (MP) DECEMBER 2010 COMPUTER SCIENCE SEMESTER 5 

Con.6019-10.                                     (REVISED COURSE)                                  GT-6705

                                                                       (3 Hours)                                     [Total Marks-100]

N.B. (1) Question No.1 is compulsory.
        (2) Solve any four out of remaining six questions.

1. a) Interface 2 input and 2 output ports of 16 bits each which can be used in hand shaking mode
        with Intel 8086 microprocessor. Show IO map and IO address table. [5 Marks]
    b) Explain addressing modes of Intel 8085 microprocessor with example. [5 Marks]
    c) Explain tightly coupled multiprocessor configuration. [5 Marks]
    d) Answer the following questions in brief:
         i) What type number and interrupt vector table addresses are assigned to NMI? [1 Marks]
        ii) Write an instruction that will mask off all bits but bit 7 of that data word stored at
             address DS:0100H. [1 Marks]
       iii) Explain the differences between Intel 8086 and 8088 processors. [2 Marks]
       iv) Explain ORG assembler directive. [1 Marks]

2. (a) Design a 8086 based microprocessor system with the following specifications:- [10 Marks]
          i) 8086 is working at 8 Mhz.
         ii) 32KB EPROM using 16 KB devices.
        iii) 64KB SRAM using 32KB devices.
             Explain the design and show memory map.
    (b) Write an assembly language program for Intel 8086 processor to exchange the blocks of
          1kb located at 0100H and 0200H, using string instructions. [10 Marks]

3. (a)Draw interfacing diagram of 3 Programmable interrupt controllers connected to Intel
        8086 microprocessor and explain it's working with CPU. [10 Marks]
    (b) Explain the concept of DMA. Explain various operating modes of 8237A. [10 Marks]

4. (a) Explain with diagram the signals carried by the individual pins of port C of 8255A when port A
         and port B are working in mode I. [10 Marks]
    (b) Explain the modes of operations of 8254. [10 Marks]

5. (a) Explain the different ways in which the parameters are passed on to the procedure. Write
         an interactive assembly language program to find the factorial of a given number using far
         procedure. [10 Marks]
    (b) Explain the different bus arbitration techniques with their advantages and disadvantages.
          [10 Marks] 

6. (a) Explain the control word format of 8254 and explain it's operation in mode 0 with a
         neat diagram. [10 Marks] 
    (b) Explain any 2 instructions of the following with example. Clearly state the way different flags
         are effected when they are executed: [6 Marks]
          A) DAS  B) IDIV  C) XLAT  D) Test
    (c) Explain the following assembler directives: [4 Marks]
         A) ASSUME  B) EVEN
7. Explain the following: - [20 Marks]
     A) IEEE 488 GPIB
     B) Difference between memory mapped IO and IO mapped IO.
     C) RS 232 C serial interface standard
     D) Memory segmentation in Intel 8086

Friday, June 6, 2014

MICROPROCESSOR (MP) MAY 2013 SEMESTER 5 COMPUTER SCIENCE

MICROPROCESSOR (MP) MAY 2013 SEMESTER 5 COMPUTER SCIENCE

Con. 6953-13.                                                                                          GS-8871
                                                       (3 Hours)                                 [Total Marks : 100]

N.B. : (1) Question No. 1 is compulsory.
          (2) Solve any four questions out of the remaining six questions.

1. (a)Explain the memory segmentation in Intel 8086 processor with its advantages and10
disadvantages.
    (b)Explain interrupts of Intel 8086 microprocessor.10

2. (a)

Design an 8086 based system with following specification :-

10
           (i) 8086 working at 8MHz
          (ii) 32 kbytes EPROM using 16kB devices
         (iii) 64 kbytes RAM using 32kB devices
Draw the complete schematic of the design indicating address map.
    (b)Explain the following Intel 8086 assembly language instructions giving example.10
      (1) TEST     (2) NOP   (3) STOS     (4) DAA   (5) SAR.

3. (a)

Explain the operating modes of 8255 PPI including the handshaking operation.

10
    (b)Explain the operating modes of 8254 PIT.10

4. (a)

Explain the modes of operation of DMA controller.

10
    (b)What do you understand by bus arbitration ? Explain the different bus arbitration10
techniques with diagram.

5. (a)

Explain the 8288 bus controller block diagram. Explain its use.

10
    (b)Explain the operation of three 8259 PIC in cascaded mode.10

6. (a)

Explain with neat diagram memory read and write machine cycle in maximum

10
mode.
    (b)Explain addressing modes of 8085 microprocessor with example.10

7.

Write a short notes on (any four) :-

20
   (a) RS-232 Serial Interface Standard
   (b) 8284 clock generator
   (c) Fixed port and Variable port addressing
   (d) Generation of Reset Signal in 8086 based system
   (e) String Instructions.

Thursday, June 5, 2014

MICROPROCESSOR (MP) DECEMBER 2013 SEMESTER 5 COMPUTER SCIENCE

MICROPROCESSOR (MP) DECEMBER 2013 SEMESTER 5 COMPUTER SCIENCE

Con. 6761-13.                                                                                            LJ-11300
                                                    (3 Hours)                                      [Total Marks : 100]

N.B. : (1) Question no. 1 is compulsory.
          (2) Answer any four questions from remaining six.
          (3) Assume suitable data if necessary.

1.Design 8086 based minimum mode system for following requirements.20
    (a)256 KB ROM using 32 KB x 8 devices.
    (b)512 KB RAM using 64 KB x 8 devices.
    (c)2-Nos 8-bit parallel port.
    (d)Support top 15 interrupts.

2. (a)

What is segmentation ? What are the merits and demerits of segmentation ?

10
    (b)What is maximum mode of 8086 ? How it differs from minimum mode ?10

3. (a)

Draw and explain the architecture of 8086.

10
    (b)Draw and explain architecture of 8255.10

4. (a)

Explain the interrupt structure of 8086 processor.

10
    (b)Explain 8085 processor with neat block diagram.10

5.

Discuss different multiprocessor systems with merits and demerits of each.

20

6. (a)

Explain the concept of DMA. Also, explain different modes of 8237 A.

10
    (b)What is bus arbitration ? Discuss various arbitration techniques.10

7.

Write short notes on :-
       (a) Instruction set of 8085.5
       (b) Addressing modes of 8086.5
       (c) 8253-Programmable interrupt timer.5
       (d) IEEE 488.5